Skip to main content

Project accounting 3 - Dynamics AX 2012 - indirect cost / burden

I was tasked with getting an indirect cost setup to work in project accounting 3, but encountered some problems.

Having read the excellent set up guide at http://www.dynamicscare.com/blog/index.php/applying-indirect-burden-costs-to-project-ax-2012-labor-actuals/comment-page-1#comment-3324  (Thanks to Merrie Cosby for this) I proceeded to make the set up according to this guide, but failed to get it working. :(

After some debugging I found that there is an error in the calculation of indirect costs when you run Dynamics AX 2012 in other languages than english.

When setting up Compounding Rules the “Base amount” that you chose, is actually hardcoded in the logic that makes the calculations.

The error can be found in

class PSAIndirectCostCalculation
method calculate:

#define.BaseComponent(‘Base amount’)

This could be corrected so that the define is

#define.BaseComponent(“@SYS73028″)

And the check for the BaseComponent

if (_sId == #BaseComponent)

is changed to

if (_sId == strFmt(#BaseComponent))

Then at least it works in danish language. :0)

Comments

  1. I talked to a colleague, and he told me that he had corrected the same error in Dynamics AX 2009, so the bug might be present in that version to.

    ReplyDelete

Post a Comment

Popular posts from this blog

Suppressing the infolog

Supressing the infolog is often useful in D365FO when augmenting code. When augmenting code using COC (Chain Of Command), you can have new code run either before or after the code you are augmenting. This means that any infolog-messages that the standard application code does, will be shown to the user, even if your augmentation supports a scenario where there must be no infolog-messages. How do you avoid the standard application infolog-messages ? To the rescue comes temporary supression of the infolog. The suppression consists of: 1) Saving the current infologLevel 2) Setting the infologLevel to SysInfologLevel::None 3) Run your code 4) Restoring the saved infologLevel to the infolog For example a table could have a validatewrite-method that validates that you are only allowed to use 3 out of 6 options in an enum-field, and you need to allow for a fourth one. Table a - validateWrite method: boolean validateWrite() {     Switch (this.enumField)     {         boolean ret;         case

Dynamics ax 2012 traversing selected records in a form data source

A classical developer challenge in Dynamics AX is to enable a form button when multiple records have been selected in the form by the user. This usually involves writing some form of loop (for or while or do-while) that starts out with calling _ds.getFirst() and continuing the loop as long as _ds.getNext() returns a tablebuffer. Well things got a little bit easier in AX 2012. In AX 2012 you can use the MultiSelectionHelper class. One example is the following that I encountered in AX 2012: Can you make the customer collection letter print out run for each selected collection record in the Print/Post collection letters form (Accounts receiveable / Periodic / Collections / Print/Post Collection letters). If we ignore the possibility for setting up print destination for running each report we can do this in two steps: 1) Change the "Multiselect" property of the "MenuButton" and the "Menuitembutton" in the MenuButton in the form from "Auto&quo

Indicating mandatory field in a dialog (RunBase) class.

A classical problem is indicating that a field is mandatory in a dialog, when the field is not bound to a datasource/field in a datasource. Normally fellow developers will tell you that, that is not possible. I found a way to do this. In your Runbase-based class you can implement the putToDialog-method e.g like this: protected void putToDialog() { super(); fieldMask.fieldControl().mandatory(true); } where fieldMask is a DialogField object in your dialog. This will make the field act like it was a mandatory field from a datasource in a form, showing a red-wavy line under the field, and requiring the field to have a value. Attention: Your class has to run on the client.If you set your class to run on the server, you get a run-time error, when the fieldMask.FieldControl()-call is made.